Search Results for dispersion blade
M-M-30117 HS100
. • Dispersion Blades, 304SS: - 4” design ‘A’ blade on 1.5 & 2 HP units. - 5” design ‘A’ blade on 3, speed hand-wheel setting. In general the disperser is run at blade tip speeds of 2500 to 5000 feet, to try first on materials handled at your facility. Under normal operation the blade is located from 1 to 1.5 blade diameters from the bottom. If this results in an excessive vortex, the blade may be lowered. If the action is a little slow at the above location, the blade may be raised to a limit
M-M-30117HS100.300Series (1)
. • Dispersion Blades, 304SS: - 4” design ‘A’ blade on 1.5 & 2 HP units. - 5” design ‘A’ blade on 3, speed hand-wheel setting. In general the disperser is run at blade tip speeds of 2500 to 5000 feet, to try first on materials handled at your facility. Under normal operation the blade is located from 1 to 1.5 blade diameters from the bottom. If this results in an excessive vortex, the blade may be lowered. If the action is a little slow at the above location, the blade may be raised to a limit
New Lift Mixer from INDCO
switch - Physical shaft guard - Front-facing E-stop - Shipped with bowtie impeller (dispersion blade available upon request) - Container bracket – easy hand knob retention system - White epoxy
A_Basic_System_Design_Primer
bubbles is the product of shear rate and fluid viscosity. Dispersion blades, homogenizers and rotor
M-M-30119 HSD Series
• Two, 3/8” diameter x 12” impeller shafts. • One, 2” diameter Design ‘A’ dispersion blade. • One, • One, 3/8” diameter x 12” impeller shaft. • One, 2” diameter Design ‘A’ dispersion blade. • Support, . • Needle valve for speed control. • One, 4” diameter Design ‘A’ dispersion blade. • Air lift cylinder, - stainlessC-TS0381 210.Bladeadapter, 2-piece (dispersion blade to shaft) - stainlessC-SA3001, outside a container. In general the disperser is run at blade tip speeds of 2500 to 5000 feet per
M-M-30118 HS5 Series
: 1.25” dia. - 316 stainless steel. • 6” design ‘A’ disperser blade - 304 stainless steel. • Pneumatic, in open air. • Never run impeller outside a container. Dispersion “rules of thumb” include, the disperser is run at blade tip speeds of 4,000 to 6,000 Feet-Per-Minute. FPM = rpm x 0.262 x blade, speed to try first on materials handled at your facility. The blade should equal 1/3rd the tank diameter and be center, vertical mounted. Under normal operation the blade is located from 1 to 1.5
HS Disperser Manual
. • Always ground the unit. • Never run the unit with the dispersion blade in open air. • Never adjust, . with 2” design ‘A’ blade - 304SS. • Adjustable chuck - 5/8”. • Hand knob control for varying speedon, mounting bolts tight? 2. Is disperser blade mounting bolt tight? 3. Has electric motor been wired, at blade tip speeds of 2500 to 5000 feet per minute. The lower ranges are used for agitation, normal operation the blade is located from 1 to 1.5 blade diameters from the bottom. If this results
HSM-03V Product Manual
offers the speed and torque characteristics to handle challenging mixing and dispersion applications, ) or optional marine style, hydrofoil, and axial turbine impellers or one of multiple available dispersion blade designs. Safety: Please follow the below safety precautions. If there are any questions, majority of mixing and dispersion applications. Torque control mode may be selected when direct control